TESDA TRAINING REGULATIONS FOR PIPEFITTING (METALLIC) NC II
The TESDA Course in PIPEFITTING (METALLIC) NC II consists of competencies that workers must achieve to enable them to perform tasks applied to rigid piping such as structural pipes, main pipes and services pipes as applied to water, oil and gas lines.
This qualification is packaged from the competency map of Construction Sector
A student who has achieved this Course in PIPEFITTING (METALLIC) NC II is competent to be:
- Pipefitter
TRAINEE ENTRY REQUIREMENTS
Trainees or students wishing to gain entry into this course should possess the following requirements:
- At least Junior High School Level Completer or an Alternative Learning System (ALS) Certificate of Completion with Grade 10 equivalent holder
- Can communicate both orally and in writing
PIPEFITTING (METALLIC) NC II COURSE – TRAINING AND REGULATION MODULE
Course Title: PIPEFITTING (METALLIC)
Level: NC II
Nominal Training Duration : 221 Hours
- 37 Hours (Basic Competencies)
- 24 Hours (Common Competencies)
- 160 Hours (Core Competencies)
This course is designed to provide the learner with knowledge, practical skills and attitude, applicable in performing work activities involve in preparing pipefitting materials, tools and equipment for spool pipe connection, installing above ground, overhead and underground piping system. This includes classroom learning activities and practical work in actual work site or simulation area.
Upon completion of the course, the learners are expected to demonstrate the above-mentioned competencies to be employed. To obtain this, all units prescribed for this qualification must be achieved.
COMPETENCIES REQUIRED IN PIPEFITTING (METALLIC) NC II
This units of competency comprising this qualification include Basic, Common and Core Competencies. To obtain this course, all units prescribed for this qualification must be achieved.
These units of competency comprising this qualification include the following:
UNIT CODE | CORE COMPETENCIES (160 Hours) |
---|---|
CON712301 | Prepare pipefitting materials, tools and equipment for spool pipe connection |
CON712302 | Install above ground piping system |
CON712303 | Install overhead piping system |
CON712304 | Install underground piping system |
UNIT CODE | COMMON COMPETENCIES (24 Hours) |
CON931201 | Prepare construction materials and tools |
CON311201 | Observe procedures, specifications and manuals of instruction |
CON311203 | Perform mensuration’s and calculations |
CON311204 | Maintain tools and equipment |
UNIT CODE | BASIC COMPETENCIES (37 Hours) |
400311210 | Participate in workplace communication |
400311211 | Work in a team environment |
400311212 | Solve/address general workplace problems |
400311213 | Develop career and life decisions |
400311214 | Contribute to workplace innovation |
400311215 | Present relevant information |
400311216 | Practice occupational safety and health policies and procedures |
400311217 | Exercise efficient and effective sustainable practices in the workplace |
400311218 | Practice entrepreneurial skills in the workplace |
This section gives the details of the contents of the core units of competency required in PIPEFITTING (METALLIC) NC II.
CORE COMPETENCIES
Core competency units comprising the qualification in PIPEFITTING (METALLIC) NC II
UNIT OF COMPETENCY : PREPARE PIPEFITTING MATERIALS, TOOLS AND EQUIPMENT FOR SPOOL PIPE CONNECTION
UNIT CODE : CON712301
This unit covers the knowledge, skill and attitudes required to productively prepare pipefitting materials, tools and equipment for spool pipe connection.
- Plan and prepare for work
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Approved construction drawings are secured and requirements are reviewed according to job specifications and work schedule requirements
- Materials, tools and equipment are secured according to bill of quantities in the approved construction drawings.
- Quality/Occupational health, safety and environmental plans are complied
- Materials, tools and equipment are prepared in accordance to work requirements
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Prepare and lay-out pipes
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Marked and measured pipes are checked according to approved construction drawings
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Joint pipes and fittings
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/ Occupational health, safety and environmental plans are complied.
- Cutting procedure is performed following job specifications
- Dimensional checking is performed according to work specification
- Pipe orientation and alignment are performed following work specification
- Joint dimensional requirements are performed following welding procedures specification
- Threaded pipe and fittings are tightened following tightening specifications
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Perform housekeeping
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards.
- Excess/un-used materials are recovered and stockpiled according to company rules and procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Tools and other materials are cleaned after use
- Required output is completed as specified by the immediate supervisor based on work schedule.
UNIT OF COMPETENCY : INSTALL ABOVE GROUND PIPING SYSTEM
UNIT CODE : CON712302
This unit covers the knowledge, skills and attitude required to productively install and fit-up above ground piping system.
- Plan and prepare for work
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Approved construction drawings are secured and requirements are reviewed according to job specifications and work schedule requirements
- Materials, tools and equipment are secured according to bill of quantities in the approved construction drawings
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are prepared in accordance to work requirements
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Laying of pipes
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Marked and measured pipes are checked according to approved construction drawings
- Installed supports are checked based on approved construction drawings
- Pipes are lifted and laid using appropriate lifting equipment in accordance with approved construction drawings
- Clamping devices are tightened to requirement
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule
- Install and fit-up piping system
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/ Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Pipes are installed according to approved construction drawings
- Pipe alignment and fit-up are performed according to approved construction drawings and procedures
- Installation and fit-up are checked according to approved procedure
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Attach pipe connectors
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Pipe connectors are installed according to approved construction procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Perform housekeeping
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards.
- Excess/un-used materials are recovered and stockpiled according to company rules and procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Tools and other materials are cleaned after use
- Required output is completed as specified by the immediate supervisor based on work schedule.
UNIT OF COMPETENCY : INSTALL OVERHEAD PIPING SYSTEM
UNIT CODE : CON712303
This unit covers the knowledge, skills and attitude required to productively install and fit-up overhead piping system.
- Plan and prepare for work
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Approved construction drawings are secured and requirements are reviewed according to job specifications and work schedule requirements
- Materials, tools and equipment are secured according to bill of quantities in the approved construction drawings
- Quality/ Occupational health, safety and environmental plans are complied
- Materials, tools and equipment are prepared in accordance to work requirements
- Work area is cleaned according to safety and environmental regulations(e.g. PD 1152 Section 6, 8 & 42) (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Laying of pipes
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Installed hangers and supports are checked based on approved construction drawings
- Pipes for horizontal installation are lifted in the working platform and laid using appropriate lifting equipment in accordance with approved construction drawings
- Pipes for vertical installation are lifted, using appropriate lifting equipment in accordance with approved construction drawings, in the required position area and clamped/ hand tightened
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Install and fit-up piping system
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/ Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Pipe alignment fit-up and tack weld are performed according to approved construction drawings and procedures
- Installation and fit-up are checked according to approved procedure
- Work area is cleaned according to safety and environmental regulations(e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Attach pipe connectors
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/ Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Materials, tools and equipment are withdrawn following company standard operating procedures
- Pipe connectors are installed according to approved construction procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Perform housekeeping
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards.
- Excess/un-used materials are recovered and stockpiled according to company rules and procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Tools and other materials are cleaned after use
- Required output is completed as specified by the immediate supervisor based on work schedule.
UNIT OF COMPETENCY : INSTALL UNDERGROUND PIPING SYSTEM
UNIT CODE : CON712304
This unit covers the knowledge, skills and attitude required to productively install and fit-up for underground piping system.
- Plan and prepare for work
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Approved construction drawings are secured and requirements are reviewed according to job specifications and work schedule requirements
- Materials, tools and equipment are secured according to bill of quantities in the approved construction drawings
- Quality/Occupational health, safety and environmental plans are complied
- Materials, tools and equipment are prepared in accordance to work requirements
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Laying of pipes
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Installed supports are checked based on approved construction drawings
- Pipes are laid using appropriate equipment in accordance with approved construction drawings
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Attach pipe connectors
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/ Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Pipe connectors are installed according to approved construction procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Install and fit-up piping system
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards
- Quality/Occupational health, safety and environmental plans are complied.
- Materials, tools and equipment are requested and withdrawn following company standard operating procedures
- Pipes are installed according to approved construction drawings
- Pipe alignment and fit-up are performed according to approved construction drawings and procedures
- Location of pipes are checked according to approved construction drawings
- Installation and fit-up are checked according to approved procedure
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Required output is completed as specified by the immediate supervisor based on work schedule.
- Perform housekeeping
- Personal protective equipment (PPE) is used in accordance with Rule 1080 of Occupational Safety and Health Standards.
- Excess/un-used materials are recovered and stockpiled according to company rules and procedures
- Work area is cleaned according to safety and environmental regulations (e.g. PD 1152 Section 6, 8 & 42)
- Tools and other materials are cleaned after use
- Required output is completed as specified by the immediate supervisor based on work schedule.
COMMON COMPETENCIES
UNIT OF COMPETENCY : PREPARE CONSTRUCTION MATERIALS AND TOOLS
UNIT CODE : CON931201
This unit covers the knowledge, skills and attitudes on identifying, requesting and receiving construction materials and tools in various workplace settings.
- Identify materials
- Materials are identified as per job requirements
- Quantity and description of materials and tools conform with the job requirements
- Tools and accessories are identified according to job requirements
- Prepare requisition of materials
- Materials and tools needed are requested according to the identified requirements
- Request is done as per company standard operating procedures (SOP)
- Substitute materials and tools are provided without sacrificing cost and quality of work
- Receive and inspect materials
- Materials and tools issued are inspected as per quantity and specification
- Tools, accessories and materials are checked
- Materials and tools are set aside to appropriate location
UNIT OF COMPETENCY : OBSERVE PROCEDURES, SPECIFICATIONS AND MANUALS OF INSTRUCTIONS
UNIT CODE : CON311201
This unit covers the knowledge, skills and attitudes On identifying, interpreting, applying services to specifications and manuals and storing manuals.
- Identify and access specification/ manuals
- Appropriate manuals are identified and accessed as per job requirements
- Version and date of manual are checked to ensure that correct specification and procedures are identified
- Interpret manuals
- Relevant sections, chapters of specifications/ manuals are located in relation to the work to be conducted
- Information and procedure in the manual are interpreted in accordance with industry practices
- Apply information in manual
- Manual is interpreted according to job requirements
- Work steps are correctly identified in accordance with manufacturer’s specification
- Manual data are applied according to the given task
- All correct sequencing and adjustments are interpreted in accordance with information contained on the manual or specifications
- Store manuals
- Manual or specification is stored appropriately to prevent damage, ready access and updating of information when required in accordance with company requirements
UNIT OF COMPETENCY : PERFORM MENSURATIONS AND CALCULATIONS
UNIT CODE : CON311203
UNIT DESCRIPTOR : This unit covers the knowledge, skills and attitudes on identifying and measuring objects based on the required performance standards.
- Select measuring instruments
- Object or component to be measured is identified, classified and interpreted according to the appropriate regular geometric shape
- Measuring tools are selected/identified as per object to be measured or job requirements
- Correct specifications are obtained from relevant sources
- Measuring instruments are selected according to job requirements
- Alternative measuring tools are used without sacrificing cost and quality of work
- Carry out measurements and calculations
- Measurements are obtained according to job requirements
- Alternative measuring tools are used without sacrificing cost and quality of work
- Calculations needed to complete work tasks are performed using the four basic process of addition (+), subtraction (-), multiplication (x) and division (/)
- Calculations involving fractions, percentages and mixed numbers are used to complete workplace tasks
- Numerical computation is self-checked and corrected for accuracy
- Instruments are read to the limit of accuracy of the tool
- Systems of measurement identified and converted according to job requirements/ISO
- Workpieces are measured according to job requirements
UNIT OF COMPETENCY : MAINTAIN TOOLS AND EQUIPMENT
UNIT CODE : CON311204
This unit covers the knowledge, skills and attitudes on checking condition, performing preventive maintenance and storing of construction painting tools and equipment.
- Check condition of tools and equipment
- Materials, tools and equipment are identified according to classification and job requirements
- Non-functional tools and equipment are segregated and labeled according to classification
- Safety of tools and equipment are observed in accordance with manufacturer’s instructions
- Condition of Personal Protective Equipment (PPE) are checked in accordance with manufacturer’s instructions
- Perform basic preventive maintenance
- Appropriate lubricants are identified according to types of equipment
- Tools and equipment are lubricated according to preventive maintenance schedule or manufacturer’s specifications
- Measuring instruments are checked and calibrated in accordance with manufacturer’s instructions
- Tools are cleaned and lubricated according to standard procedures
- Defective instruments, equipment and accessories are inspected and replaced according to manufacturer’s specifications
- Tools are inspected, repaired and replaced after use
- Work place is cleaned and kept in safe state in line with Occupational Safety and Health (OSHS)
- Store tools and equipment
- Inventory of tools, instruments and equipment are conducted and recorded as per company practices
- Tools and equipment are stored safely in appropriate locations in accordance with manufacturer’s specifications or company procedures
BASIC COMPETENCIES
UNIT OF COMPETENCY : PARTICIPATE IN WORKPLACE COMMUNICATION
UNIT CODE : 400311210
This unit covers the knowledge, skills and attitudes required to gather, interpret and convey information in response to workplace requirements.
- Obtain and convey workplace information
- Specific and relevant information is accessed from appropriate sources
- Effective questioning , active listening and speaking skills are used to gather and convey information
- Appropriate medium is used to transfer information and ideas
- Appropriate non- verbal communication is used
- Appropriate lines of communication with supervisors and colleagues are identified and followed
- Defined workplace procedures for the location and storage of information are used
- Personal interaction is carried out clearly and concisely
- Perform duties following workplace instructions
- Written notices and instructions are read and interpreted in accordance with organizational guidelines
- Routine written instruction are followed based on established procedures
- Feedback is given to workplace supervisor based instructions/ information received
- Workplace interactions are conducted in a courteous manner
- Where necessary, clarifications about routine workplace procedures and matters concerning conditions of employment are sought and asked from appropriate sources
- Meetings outcomes are interpreted and implemented
- Complete relevant work related documents
- Range of forms relating to conditions of employment are completed accurately and legibly
- Workplace data is recorded on standard workplace forms and documents
- Basic mathematical processes are used for routine calculations
- Errors in recording information on forms/ documents are identified and properly acted upon
- Reporting requirements to supervisor are completed according to organizational guidelines
UNIT OF COMPETENCY: WORK IN TEAM ENVIRONMENT
UNIT CODE : 400311211
This unit covers the skills, knowledge and attitudes to identify role and responsibility as a member of a team.
- Describe team role and scope
- The role and objective of the team is identified from available sources of information
- Team parameters, reporting relationships and responsibilities are identified from team discussions and appropriate external sources
- Identify own role and responsibility within team
- Individual role and responsibilities within the team environment are identified
- Roles and responsibility of other team members are identified and recognized
- Reporting relationships within team and external to team are identified
- Work as a team member
- Effective and appropriate forms of communications used and interactions undertaken with team members who contribute to known team activities and objectives
- Effective and appropriate contributions made to complement team activities and objectives, based on individual skills and competencies and workplace context
- Observed protocols in reporting using standard operating procedures
- Contribute to the development of team work plans based on an understanding of team’s role and objectives and individual competencies of the members.
UNIT OF COMPETENCY : SOLVE/ADDRESS GENERAL WORKPLACE PROBLEMS
UNIT CODE : 400311212
This unit covers the knowledge, skills and attitudes required to apply problem-solving techniques to determine the origin of problems and plan for their resolution. It also includes addressing procedural problems through documentation, and referral.
- Identify routine problems
- Routine problems or procedural problem areas are identified
- Problems to be investigated are defined and determined
- Current conditions of the problem are identified and documented
- Look for solutions to routine problems
- Potential solutions to problem are identified
- Recommendations about possible solutions are developed, documented, ranked and presented to appropriate person for decision
- Recommend solutions to problems
- Implementation of solutions are planned
- Evaluation of implemented solutions are planned
- Recommended solutions are documented and submit to appropriate person for confirmation
UNIT OF COMPETENCY : DEVELOP CAREER AND LIFE DECISIONS
UNIT CODE : 400311213
This unit covers the knowledge, skills, and attitudes in managing one’s emotions, developing reflective practice, and boosting self-confidence and developing self-regulation.
- Manage one’s emotion
- Self-management strategies are identified
- Skills to work independently and to show initiative, to be conscientious, and persevering in the face of setbacks and frustrations are developed
- Techniques for effectively handling negative emotions and unpleasant situation in the workplace are examined
- Develop reflective practice
- Personal strengths and achievements, based on self-assessment strategies and teacher feedback are contemplated
- Progress when seeking and responding to feedback from teachers to assist them in consolidating strengths, addressing weaknesses and fulfilling their potential are monitored
- Outcomes of personal and academic challenges by reflecting on previous problem solving and decision making strategies and feedback from peers and teachers are predicted
- Boost self-confidence and develop self-regulation
- Efforts for continuous self-improvement are demonstrated
- Counter-productive tendencies at work are eliminated
- Positive outlook in life are maintained.
UNIT OF COMPETENCY : CONTRIBUTE TO WORKPLACE INNOVATION
UNIT CODE : 400311214
This unit covers the knowledge, skills and Attitudes required to make a pro-active and positive contribution to workplace innovation.
- Identify opportunities to do things better
- Opportunities for improvement are identified proactively in own area of work.
- Information are gathered and reviewed which may be relevant to ideas and which might assist in gaining support for idea.
- Discuss and develop ideas with others
- People who could provide input to ideas for improvements are identified.
- Ways of approaching people to begin sharing ideas are selected.
- Meeting is set with relevant people.
- Ideas for follow up are review and selected based on feedback.
- Critical inquiry method is used to discuss and develop ideas with others.
- Integrate ideas for change in the workplace
- Critical inquiry method is used to integrate different ideas for change of key people.
- Summarizing, analyzing and generalizing skills are used to extract salient points in the pool of ideas.
- Reporting skills are likewise used to communicate results.
- Current Issues and concerns on the systems, processes and procedures, as well as the need for simple innovative practices are identified.
UNIT OF COMPETENCY : PRESENT RELEVANT INFORMATION
UNIT CODE : 400311215
This unit of covers the knowledge, skills and attitudes required to present data/information appropriately.
- Gather data/ information
- Evidence, facts and information are collected
- Evaluation, terms of reference and conditions are reviewed to determine whether data/information falls within project scope
- Assess gathered data/ information
- Validity of data/ information is assessed
- Analysis techniques are applied to assess data/ information.
- Trends and anomalies are identified
- Data analysis techniques and procedures are documented
- Recommendations are made on areas of possible improvement.
- Record and present information
- Studied data/information are recorded.
- Recommendations are analysed for action to ensure they are compatible with the project’s scope and terms of reference.
- Interim and final reports are analysed and outcomes are compared to the criteria established at the outset.
- Findings are presented to stakeholders.
UNIT OF COMPETENCY : PRACTICE OCCUPATIONAL SAFETY AND HEALTH POLICIES AND PROCEDURES
UNIT CODE : 400311216
This unit covers the knowledge, skills and attitudes required to identify OSH compliance requirements, prepare OSH requirements for compliance, perform tasks in accordance with relevant OSH policies and procedures
- Identify OSH compliance requirements
- Relevant OSH requirements, regulations, policies and procedures are identified in accordance with workplace policies and procedures
- OSH activity non-conformities are conveyed to appropriate personnel
- OSH preventive and control requirements are identified in accordance with OSH work policies and procedures
- Prepare OSH requirements for compliance
- OSH work activity material, tools and equipment requirements are identified in accordance with workplace policies and procedures
- Required OSH materials, tools and equipment are acquired in accordance with workplace policies and procedures
- Required OSH materials, tools and equipment are arranged/ placed in accordance with OSH work standards
- Perform tasks in accordance with relevant OSH policies and procedures
- Relevant OSH work procedures are identified in accordance with workplace policies and procedures
- Work Activities are executed in accordance with OSH work standards
- Non-compliance work activities are reported to appropriate personnel
UNIT OF COMPETENCY : EXERCISE EFFICIENT AND EFFECTIVE SUSTAINABLE PRACTICES IN THE WORKPLACE
UNIT CODE : 400311217
This unit covers knowledge, skills and attitude to identify the efficiency and effectiveness of resource utilization, determine causes of inefficiency and/or ineffectiveness of resource utilization and Convey inefficient and ineffective environmental practices
- Identify the efficiency and effectiveness of resource utilization
- Required resource utilization in the workplace is measured using appropriate techniques
- Data are recorded in accordance with workplace protocol
- Recorded data are compared to determine the efficiency and effectiveness of resource utilization according to established environmental work procedures
- Determine causes of inefficiency and/or ineffectiveness of resource utilization
- Potential causes of inefficiency and/or ineffectiveness are listed
- Causes of inefficiency and/or ineffectiveness are identified through deductive reasoning
- Identified causes of inefficiency and/or ineffectiveness are validated thru established environmental procedures
- Convey inefficient and ineffective environmental practices
- Efficiency and effectiveness of resource utilization are reported to appropriate personnel
- Concerns related resource utilization are discussed with appropriate personnel
- Feedback on information/ concerns raised are clarified with appropriate personnel
UNIT OF COMPETENCY : PRACTICE ENTREPRENEURIAL SKILLS IN THE WORKPLACE
UNIT CODE : 400311218
This unit covers the outcomes required to apply entrepreneurial workplace best practices and implement cost-effective operations
- Apply entrepreneurial workplace best practices
- Good practices relating to workplace operations are observed and selected following workplace policy.
- Quality procedures and practices are complied with according to workplace requirements.
- Cost-conscious habits in resource utilization are applied based on industry standards.
- Communicate entrepreneurial workplace best practices
- Observed Good practices relating to workplace operations are communicated to appropriate person.
- Observed quality procedures and practices are communicated to appropriate person
- Cost-conscious habits in resource utilization are communicated based on industry standards.
- Implement cost-effective operations
- Preservation and optimization of workplace resources is implemented in accordance with enterprise policy
- Judicious use of workplace tools, equipment and materials are observed according to manual and work requirements.
- Constructive contributions to office operations are made according to enterprise requirements.
- Ability to work within one’s allotted time and finances is sustained.
GLOSSARY OF TERMS
- DOWEL – A headless, cylindrical pin which, is sunk into corresponding holes
- LINTEL – Refers to the horizontal member over an opening such as door or window, usually carrying the load
- MORTAR – Refers to a mixture of cement, sand and water used for laying bricks or masonry units
- REBAR – Refers to the reinforcing bars that are embedded in building components such as concrete, masonry walls, columns, beams and other structural parts
- SCAFFOLD – Refers to a temporary or movable platform supported on the ground or suspended, used for working at considerable heights above the ground.
- FORMWORKS – A set of wood or steel forms in place to hold wet concrete until it hardens
- CURING – Is defined as providing adequate moisture, temperature, and time to allow the concrete to achieve the desired properties for its intended use.
- 5S – The five in a 5S workplace organizational and housekeeping methodology refers to five steps – sort, set in order, shine, standardize and sustain.
- 3R – The principle of reducing waste, reusing and recycling resources and products
- Reduce – The waste management concept of reducing what is produced and what is consumed
- Reuse – The waste management concept of reusing items, or re-purposing them for a use different than what they are intended for
- Recycling – The waste management concept of transforming again into a raw material that can be shaped into a new item
Available pi ba ito sa iloilo area
Not available
Hi any recommendation for accredited center for Pipe Fitting near in Quezon City? TIA
Not available in Quezon City
Meron ba Dito sa cebu pipe fitting metallic
Saint James Academy of Skills Technology, Inc.
Poblacion, Compostela, Cebu
(032) 425-6061 / 260-2649
Hello,
May I know po ang school name sa Nueva Ecija and Bulacan na nag ooffer po ng Pipe Fitter (metallic) course.
Salamat
EEI Corporation
Makapilapil, San Ildefonso, Bulacan
0936-8988914
Asia Pacific College of Business and Arts, Inc.
Manzano Street, Poblacion Norte, Rizal, Nueva Ecija
0943-636-0603/ 044-9403400
Good day,
Available po ba ang pipe fitting courses sa Cagayan valley or nearby provinces?
If not, Meron po ba within Metro Manila?
Thank you
Asia Pacific College of Business and Arts, Inc.
Manzano Street, Poblacion Norte, Rizal, Nueva Ecija
0943-636-0603/ 044-9403400
Core Trades Academy, Inc.
481 San Raphael St., Brgy Plainview, Mandaluyong City
8534-2862 / 481-6023 / 3612244
wala po ba training para po sa mechanical fitter
San ang location mo?
d2 po sir sa UAE p balak q sana magtraining ng mechanical fitter if available.salamat po
Intersado po ko,north caloocan po ko
This course is not available in Caloocan
Saang training center po dito sa cavite pwd mag enroll. Interested here
This course is not available in Cavite
Eh pag hindi metallic po saan sa cavite
Not available in Cavite
Good day Po sir / ma’am
My training po ba ng pipe fitting NC11 sa TESDA Baguio?
Not available in Baguio
Pipefitting in batangas
Regional Training Center – CALABARZON
P.Herrera St., Batangas City
0917-502-1328
Ubeda Manpower Training Center Inc.
Brgy. Sto. Cristo, San Jose, Batangas
726-3596 / 0907-274-9276
Good Day maam and sir. I would like to ask lang po kung saan place ba may available na nagkaconduct nitong course. Thank you for your smooth concern.
Please inquire to the TESDA accredited school in your area
Saan po ba mayroong ng course training na to?
Nueva Ecija, Bulacan, CAgayan De Oro, Bataan, Batangas, Cebu