//pagead2.googlesyndication.com/pagead/js/adsbygoogle.js

IETI Laguna Accredited Tesda Courses

International Electronics and Technical Institute Laguna is an institution accredited by TESDA that offers Technical and Vocational Education and Training Programs (TVET) under the Technical Education and Skills Development Authority (TESDA) and the Commission on Higher Education (CHED).

IETI College of Science and Technology, San Pedro was opened in San Pedro, Laguna in 1996 offering technical courses in ITM, CTSM, EST, MEET and AET and baccalaureate courses in BS Information Technology (BSIT) and BS in Industrial Technology (BSIT) major in Electronics, Industry Electricity Computer, Refrigeration and Airconditioning and Automotive.

IETI Calamba and Lagro was opened 1997 with the initial course offerings of Information Technology Management (ITM), Computer Technician and Systems Management (CTSM), Electromechnical and Electronics Technician (MEET), Electronics Service Technician (EST).

International Electronics and Technical Institute Calamba

Address: LLED Bldg., Pabalan St., Calamba, Laguna, Philippines
Telephone Number: (049) 545-6280
Website: http://ieti.edu.ph

TESDA Approved Programs

Here is the list of available TESDA registered programs and short courses offered in “International Electronics and Technical Institute” in the province of Laguna.

List of Tesda Courses Offered / Registered Programs

Course Authorized Duration
Bookkeeping NC III 1,200 Hours
Building Wiring Installation NC II 1,080 Hours
Computer Hardware Servicing NC II 356 Hours
Computer Hardware Servicing NC II 588 hours
Consumer Electronics Servicing NC II Not Available
Electrical Installation and Maintenance NC II 1,080 Hours
Electrical Installation and Maintenance NC II 603 hours
Programming NC IV 252 Hours
Shielded Metal Arc Welding (SMAW) NC II 450 Hours

International Electronics and Technical Institute Biñan

Address: 6F Caridad Mendoza Business Center, Biñan, Laguna, Philippines
Telephone Number: (049) 511-9385/86

Course Authorized Duration
Bartending NC II 624 hrs
Bookkeeping NC III 1,200 Hours
Building Wiring Installation NC II 1,080 Hours
Computer Hardware Servicing NC II Not Available
Consumer Electronics Servicing NC II Not Available
Electrical Installation & Maintenance NC II 1,080 Hours
Food and Beverage Service NC II 436 Hours
Front Office Services NC II 472 Hours
Programming NC IV Not Available

Basic Requirements for TESDA Courses:

  • At least 18 years of age
  • At least High School Graduate
  • Copy of NSO Birth Certificate
  • With good moral character
  • Undergone a pre-training assessment
  • Can communicate both orally and in written form

Training Fees and Schedule

The cost of training and tuition fees may vary depending upon the specific course of interest and the school offering the training. Training centers also may have slightly different syllabus to teach to students in a class.

For inquiries, tuition fees, enrollment procedures, class schedule and other concern, it would be better that you visit their school/training center and inquire for other documents they may need.

Location and Contact Information

For further information, please contact the school directly at telephone number (049) 545-6280. You can also visit International Electronics and Technical Institute. The assessment center is located at LLED Bldg., Pabalan St., Calamba, Laguna, Philippines.


2 Comments

Add a Comment
  1. Good pm po maam sir! Ask ko lang po sana f my record pa po yung mga nag take po ng welder nc2 last october 9,2009, di ko pa po kasi nakuha yung certificate ko, ask ko lng po sana f my record pa po and kung pwede ko pa po makuha, thank u po

  2. magkano po ang tuition sa smaw nc2
    at ilang months po training

Leave a Reply

Your email address will not be published. Required fields are marked *

Tesda Courses © 2015 Privacy | Disclaimer | Terms of Use